- Rubber hardness testing tells you how much a rubber surface resists a small indentation.
- Shore A, Shore D and IRHD are the scales you will hear about most.
- A wrong hardness value can ruin sealing, grip, wear life and even safety.
- Sample size, thickness, temperature and conditioning change the result, so prepare samples carefully.
- BIS standards for many rubber products set hardness limits and refer to the Indian test method, IS 3400 (Part 2).
- Always check the latest version of the standard before you test or file anything.
Introduction
Think about a pencil eraser and a car tyre. Both are rubber. Now imagine the eraser was as hard as a tyre, or the tyre as soft as an eraser. Neither would work, right?
That is exactly why rubber hardness testing matters. It is one of the quickest and cheapest tests in a rubber lab, and it tells you a lot about the compound inside.
In this blog, we will keep things easy. You will learn what hardness means, which scales are used, how the test is done, where BIS comes in, and what mistakes to avoid.
What Is Rubber Hardness Testing?
Rubber hardness is the resistance of rubber to indentation. In the test, a small pointed or rounded tool (called an indenter) is pressed into the rubber surface with a fixed force. The depth it goes in is converted into a hardness number.
Soft rubber lets the tool go deep, so the number is low. Hard rubber resists, so the number is high.
It is important to know one thing. Hardness is not the same as strength. A rubber can be hard but still tear easily. So hardness is one property among many, like tensile strength, elongation and ageing resistance.
Common Hardness Scales Explained
There is no single scale for all rubbers. Each scale suits a certain range.
| Scale | Where it is used | In simple words |
|---|---|---|
| Shore A | Most soft and medium rubbers: seals, hoses, soles, gaskets | The most common scale in factories |
| Shore D | Hard rubbers, ebonite, rigid plastics | For materials too hard for Shore A |
| IRHD | Precise testing of thin or small rubber parts, O-rings | More accurate on small samples |
| Shore 00 | Very soft rubbers and foams | Used for sponge-like materials |
A rough thumb rule: if your Shore A reading goes above about 90, it is better to check with Shore D. If it goes below about 10, think about Shore 00. Do not trust readings at the very end of any scale.
Which Standards Apply?
Test methods are written down in standards so that every lab tests in the same way. You will mostly see these:
| Standard | What it covers |
|---|---|
| IS 3400 (Part 2) | Indian method for hardness of vulcanised rubber |
| ISO 48 series | International methods for rubber hardness, including IRHD |
| ISO 7619-1 | Indentation hardness by durometer (Shore method) |
| ASTM D2240 | Durometer hardness of rubber and plastics |
A simple example: a manufacturer makes rubber sealing rings and sells to an Indian customer. The product standard says hardness must be within a fixed range. The lab then follows the Indian test method, IS 3400 (Part 2), to measure it.
Standards get revised from time to time. So before you book a test, confirm which version is current. Do not depend on an old copy lying in the office.
Why Rubber Hardness Testing Is Important
- Sealing: A seal that is too hard will not close gaps. Too soft, and it gets squeezed out or deforms.
- Wear life: Hardness affects how quickly a surface wears down, like tyre tread or conveyor belts.
- Grip and comfort: Footwear soles and handles need the right softness to feel comfortable and safe.
- Quality control: Hardness is a fast check that every batch was mixed and cured properly.
- Spotting problems early: Under-curing, wrong filler quantity or wrong oil content often shows up as a hardness change.
- Customer and standard requirements: Buyers and product standards often fix a hardness range, so you need a proper report.
Types of Rubber Hardness Tests
1. Durometer (Shore) Test
This is the most used method. A handheld or stand-mounted durometer has a spring-loaded indenter. You press it flat on the rubber and read the dial or digital display after a fixed time.
It is quick and easy. For good repeatability, a stand with a fixed weight is better than pressing by hand.
2. IRHD Test
IRHD means International Rubber Hardness Degrees. A small ball indenter is pushed into the rubber with a set contact force and then a larger force. The extra depth is measured and converted to a number.
This method works well for small and curved parts such as O-rings, where a normal durometer may give a wrong reading.
3. Pocket Hardness Tester
This is a small pen-like instrument used for rough checks on the shop floor. It is useful for quick sorting, but it is not a replacement for a lab report.
How Is the Test Done? Step by Step
- Prepare the sample. The sample should have a flat, smooth surface with no dust, oil or cracks.
- Check thickness. Standard methods ask for a minimum thickness. If your part is thin, stack pieces only if the method allows it.
- Condition the sample. Keep it at standard laboratory temperature for the required time. Rubber changes with temperature, so do not skip this.
- Choose the right scale. Pick Shore A, Shore D or IRHD based on the material.
- Place the sample on a hard, flat surface. A soft table gives a false low reading.
- Apply the indenter. Press smoothly and vertically, not at an angle.
- Read after the fixed time. Many methods ask for the reading within a few seconds of firm contact.
- Repeat at different points. Take several readings, keeping a minimum distance from the edges and from each other.
- Report the result. Write the median or average, the scale, the temperature and the standard followed.
Things That Change Your Hardness Result
Many people get confused when two labs give two different numbers. Most of the time, the reason is one of these:
- Temperature: Warm rubber feels softer. Cold rubber feels harder.
- Sample thickness: A thin sample reads harder because the hard table below affects the reading.
- Distance from edge: Readings taken too near the edge come out lower.
- Surface condition: A rough, dusty or oily surface gives unstable readings.
- Time of reading: Rubber slowly creeps under load, so the number drops if you wait longer.
- Operator technique: Uneven pressure or a tilted tool changes the result.
- Instrument calibration: A durometer out of calibration will always mislead you.
- Age and cure state: A freshly moulded part may keep hardening for some days.
Two Kinds of Testing: Factory Lab vs Recognised Lab
Your own factory lab is useful for batch-wise checks. You can test every lot quickly and catch problems early.
But when a test report is needed for BIS, for a buyer or for a dispute, a recognised outside lab is the safer choice. A lab with proper accreditation, calibrated instruments and trained staff gives a report that others will accept.
A good practice is to use both. Check daily in your factory, and send samples to a recognised lab at regular gaps, or whenever you change a compound or supplier.
BIS and Rubber Hardness Testing
BIS stands for Bureau of Indian Standards, the national standards body of India. Let us be clear about one thing here. There is no separate BIS certificate that says only “rubber hardness tested”. Hardness is one of the tests inside the product standard.
So how does BIS connect to hardness? In two ways.
1. The test method. IS 3400 (Part 2) is the Indian standard test method for hardness of vulcanised rubber. Many BIS product standards refer to it when they ask for a hardness check.
2. The product requirement. When a rubber product comes under a BIS standard, the standard gives the hardness limit for that product. Your sample must meet it, along with the other tests in that standard.
Rubber is used in many products where BIS standards exist. Some examples where rubber properties matter are tyres, rubber tubing for gas use, footwear and sealing parts. Which products need a BIS licence depends on the Quality Control Orders (QCOs) and the Compulsory Registration Scheme lists in force. These change from time to time, so please check the latest BIS notifications for your product.
Simple BIS Process for a Rubber Product
- Find the Indian Standard that applies to your product.
- Read the hardness clause and the test method it points to.
- Check whether your product comes under a QCO or a compulsory scheme.
- Test samples at a lab recognised for that purpose.
- Keep factory test records ready.
- Apply for the right BIS licence or registration, if your product needs one.
- Maintain regular testing after you get approval, because BIS may do market surveillance.
No one can promise approval in advance. BIS decides after checking your documents, factory and test reports. What you can do is prepare properly, so that fewer queries come up.
Documents Usually Needed
Company documents
- Company registration or business proof
- Factory address and layout details
- Authorised person details
Product documents
- Product name, model and grade list
- Raw material details and compound information
- Drawings or product photographs
Testing records
- Hardness test report with scale and standard mentioned
- Calibration certificate of your durometer
- Batch-wise quality control records
How Long Does It Take?
The test itself is quick. Hardness testing on a sample can often be done in a short time once the sample reaches the lab and is conditioned.
The bigger time goes into the full product testing and the BIS process. That depends on how many tests the standard needs, lab schedule, document readiness and any queries raised. So plan ahead and do not wait for the last week before a deadline.
Cost of Rubber Hardness Testing
We are not giving fixed amounts here, because rates differ from lab to lab. The cost usually depends on these points:
- Number of samples and compounds
- Type of test (Shore, IRHD or a full set of rubber tests)
- Whether the test is only hardness, or part of a full BIS test package
- Urgency of the report
- Special conditioning, such as heat ageing before the hardness test
The best way is to share your product details and ask for a clear breakup before you send samples.
Common Mistakes to Avoid
- Testing a sample that is too thin and not telling the lab.
- Taking readings too close to the edge of the sample.
- Skipping temperature conditioning before the test.
- Using a durometer that was never calibrated.
- Choosing Shore A for a very hard material, just because it is easy.
- Holding the durometer by hand with uneven pressure.
- Sending a sample from a batch that is not typical of regular production.
- Using an old version of the standard and then facing mismatches in the report.
Who Needs Rubber Hardness Testing?
- Manufacturers of seals, gaskets, hoses, tyres, belts, footwear and moulded parts.
- Importers who bring rubber products into India and must show they meet the Indian standard.
- Private label brands that get products made by another factory.
- Overseas manufacturers who export to India and need proper test reports and BIS approval where it applies.
- Buyers and quality teams who want to verify supplier material.
Why Choose Diligence Certifications for rubber hardness testing Certification?
Getting the right test and the right paperwork can feel confusing, especially when you are new to BIS. That is where Diligence Certifications can help.
- The team explains which standard applies to your rubber product, in plain language.
- You get guidance on sample preparation, so common mistakes are avoided early.
- Documents are checked before filing, so there are fewer back-and-forth queries.
- Support is available for manufacturers, importers, private label brands and overseas companies.
- You can read more about the support on the BIS certification service page.
The final decision always rests with BIS and the testing lab. But with proper guidance, you walk in prepared.
Conclusion
Rubber hardness testing looks like a small test, but it carries a lot of weight. It tells you whether your rubber will seal, grip, wear and last the way it should.
Keep your samples clean and conditioned, pick the right scale, use calibrated instruments and follow the latest standard. If your product falls under BIS, treat hardness as one part of a bigger set of tests and plan the whole process early.
Do it right the first time, and you save time, money and a lot of tension.
Frequently Asked Questions
1. What is rubber hardness testing?
It is a test that measures how much rubber resists a small indentation under a fixed force. The result is shown as a hardness number on a chosen scale.
2. What is the most common scale for rubber hardness?
Shore A is the most common scale for soft and medium rubbers like seals, hoses and footwear soles.
3. When should I use Shore D instead of Shore A?
Use Shore D for harder materials. If Shore A readings come very high, near the top of the scale, Shore D is the better choice
4. What does IRHD mean?
IRHD means International Rubber Hardness Degrees. It is a method that suits small, thin or curved parts like O-rings.
5. Which Indian standard covers rubber hardness testing?
IS 3400 (Part 2) is the Indian test method for hardness of vulcanised rubber. Please confirm the latest version before testing.
6. Does temperature affect rubber hardness?
Yes. Warm rubber reads softer and cold rubber reads harder, so samples must be conditioned at standard temperature.
BIS Certification
CDSCO
PESO
CPCB
LMPC
WPC Approval
Global Approvals
TEC
ARAI
BEE
ISO Certification
DGCA Certification
NOC For Steel
APEDA Registration
Business Registration
FSSAI Mark Certification
Legal Services
Trademark Registration
Copyright Registration
Patent Registration



